Em linhas de conversão contínuas de papel alimentado com tela que funcionam a velocidades lineares superiores a 120 m/min, o adesivo a frio aplicado através de unidades de transferência de filme de três rolos deve apresentar um perfil de viscosidade de contato que impeça a rasga da fibra dentro de 2,5 s de combinação sem penetrar no substrato sob pressões de aperto de 3-5 bar. CW40-907, fornecido a 55±1% sólidos e um pH vermelho de 4,5-5,0, é reduzido à viscosidade da aplicação por pré-mistura de água potável para uma leitura Brookfield RVT (#3 fuso, 20 rpm) de 800-1200 mPa·s. Uma formulação típica de costura de saco incorpora 18-22 phr de uma dispersão de éster de colofonia hidrogenada branca de água (ponto de amolecimento 65°C) e 3-5 phr de um plastificante de éster de benzoato para diminuir a temperatura mínima de formação de filme abaixo de 2°C. A ausência de etoxilatos de alquilfenol no pacote do emulsionante elimina o fenômeno de migração superficial observado com graus NPEO-estabilizados convencionais, um fator que muda o tempo de repelência no teste de Cobb (ISO 535:2014, água absorvida por unidade de área) em 15-20% menor absorção quando a costura colada entra em contato com materiais de enchimento hidratados. Em uma linha KROENERT PAK 503, a captação de adesivos é mantida em 18–22 g/m² peso seco; O excesso de extração leva ao bloqueio dos rolos idler sucessivos quando a umidade relativa dentro do piso da oficina excede 65% — uma condição que requer ar de maquiagem desumidificado dirigido ao primeiro capô de secador. A conformidade abrange a FDA 21 CFR §176.170 (componentes de papel e papelão em contato com alimentos aquosos e gordurosos), a recomendação BfR XXXVI/1 e a EN 1720:1998 para classificação com baixo teor de formaldeído. O limiar de coagulo no bombeamento de circulação de alto cisalhamento é medido a 8 000 s ⁻ ¹ cisalhamento capilar, acima do qual uma bomba de cavidade progressiva dedicada com controle de temperatura estator é substituída por uma bomba de diafragma para limitar a entrada de calor mecânico.
Preços competitivos CW40-907 Emulsão VAE sem APEO que se ajustam ao seu orçamento - termos flexíveis e orçamentos personalizados para cada pedido.
Para amostras, preços ou mais informações, entre em contato conosco em
+8615380400285
Ou envie para
sales2@liwei-chem.com.
Responderemos a você o mais rápido possível.
Telefone: +8615380400285
E-mail: sales2@liwei-chem.com
The CW40-907 product is a vinyl acetate‑ethylene copolymer dispersion engineered without alkylphenol ethoxylate surfactants (APEO‑free), targeting adhesion and binder applications where regulatory compliance with European REACH Annex XVII Entry 46a and the EU Ecolabel for adhesives (Reference **EU 2018/680**) is non‑negotiable. Manufactured under a polyvinyl alcohol‑stabilised system, the emulsion presents as a milky‑white, medium‑viscosity fluid that yields a clear, tack‑free film upon drying at temperatures above its minimum film formation threshold. Its core distinction from conventional VAE grades lies in the complete elimination of nonylphenol and octylphenol ethoxylates—substances known to degrade to endocrine‑disrupting species in aquatic environments—replaced by a proprietary blend of fatty alcohol ethoxylates with a ready biodegradability profile exceeding **60 % ThOD** in **28 days** per **OECD 301F**. The shift in surfactant architecture not only addresses EU Ecolabel thresholds (total NP/OP ethoxylates **<300 mg/kg**) but also reduces surfactant migration to the adhesive‑substrate interphase, a mechanism often implicated in long‑term bond deterioration under humid heat aging.
How Does Surfactant Chemistry Reshape Long‑Term Adhesion and Regulatory Compliance?
When an adhesive‑bonded assembly is subjected to accelerated aging at **70 °C** and **95 % relative humidity** for **14 days**, low‑molecular‑weight APEO species can migrate to the interface, plasticise the polymer and weaken the interfacial boundary layer. CW40-907 replaces these migratory surfactants with higher‑molecular‑weight, water‑insoluble nonionic partners whose critical micelle concentration remains above **1 000 mg/L**, thereby partitioning almost completely into the polymer phase during coalescence. The immediate consequence is superior wet‑shear retention on aluminium‑to‑wood joints tested per **EN 204** D3, where the emulsion typically retains **≥85 %** of its dry shear strength after **4 h** of cold‑water immersion, compared with **70–75 %** for APEO‑containing analogues formulated at equivalent solids. From a regulatory standpoint, REACH Annex XVII prohibits the placing on the market of textile articles or mixtures for consumer use containing NP or NP ethoxylates in concentrations equal to or exceeding **0.1 % w/w** after **3 January 2021**. CW40-907 is routinely analysed by solvent extraction followed by LC‑MS/MS in accordance with **EN ISO 18254‑1** and consistently measures **<10 mg/kg** total APEO, eliminating the need for downstream repulpability or wastewater containment measures in label‑stock converting plants.
The environmental toxicity profile shifts accordingly: standard APEO‑containing VAE dispersions typically exhibit an acute EC50 to *Daphnia magna* (**OECD 202**) of **<10 mg/L**, while CW40-907 values exceed **100 mg/L**, removing the requirement for the GHS09 environmental hazard pictogram on safety data sheets. This aquatic safety margin simplifies disposal protocols in paper coating mills where backwater clarification ponds discharge to freshwater bodies.
Typical physical properties determined on production batches conditioned at **23 ± 2 °C** and **50 ± 5 % RH** are provided in the table below. These values reflect representative quality‑control data and should not be interpreted as guaranteed release limits, which are defined on the certificate of analysis for each batch.
| Property | Value | Unit | Method |
|---|
| Solids content | 55.0–57.0 | % | ISO 3251 (105 °C, 3 h) |
| Brookfield viscosity (RVT, spindle 4, 20 rpm, 23 °C) | 800–1 200 | mPa·s | ISO 2555 |
| pH | 4.5–5.5 | — | ISO 976 |
| Density | 1.07–1.09 | g/cm³ | ISO 2811‑1 |
| Minimum film formation temperature (MFFT) | <0 | °C | ISO 2115 |
| Surface tension | 38–42 | mN/m | ISO 1409 (Du Noüy ring) |
| Median particle size (D50) | 0.6–1.0 | µm | ISO 13320 |
| Residual formaldehyde | <20 | mg/kg | EN 717‑3 |
| APEO content (total NP+OP ethoxylates) | <10 | mg/kg | EN ISO 18254‑1 (LC‑MS/MS) |
Mechanical shear stability is quantified by subjecting a **200 g** sample to a laboratory high‑shear disperser (VMA Getzmann Dispermat, **40 mm** dissolver disc, **3 000 min⁻¹**) for **10 min** and sieving through a **40 µm** mesh; retained coagulum is normally **<50 mg**, a figure that predicts trouble‑free transfer through diaphragm and progressive‑cavity pumps. The MFFT of **<0 °C** is achieved without external coalescent, a feature that enables VOC‑free formulations for indoor flooring adhesives governed by German AgBB requirements.
When Alkali‑ and Water‑Immersion Resistance Dictates Tile Adhesive Formulation
In cementitious tile adhesives targeting **EN 12004** class C2, the addition of **2.5–3.0 wt%** CW40-907 (based on total dry mortar weight) profoundly alters the pore structure of the hardened matrix. Mixing is executed in a twin‑shaft compulsory mixer (Eirich R05) for **180 s** with a controlled water temperature **≤25 °C** to prevent flash‑coagulation of the polymer on contact with alkaline cement (pH **>12**). The resulting mortar exhibits an open time of **≥20 min** per **EN 1346**, a 28‑day compressive strength of **≥15 MPa** per **EN 1015‑11**, and a tensile adhesion strength after **21 days** water immersion of **≥1.0 MPa** when tested with a ceramic tile on concrete substrate per **EN 1348**. The PVOH‑rich protective colloid system resists alkaline hydrolysis far longer than surfactant‑only stabilised grades; after **28 days** of storage in a **40 °C**/**100 % RH** chamber, retained adhesion remains above **90 %**, whereas a fully surfactant‑stabilised APEO‑free analogue may drop to **75 %**. This resistance profile is critical for green concrete applications where residual moisture and high pH persist for months.
The absence of APEO also permits the direct recycling of wash water from trowel‑cleaning stations into the mixing water circuit, as ecotoxicological loading stays below trigger values ( **EC50>100 mg/L** ). Production‑scale trials on a M‑technic industrial mixing plant revealed no measurable foaming penalty or slump change across **12 consecutive batches**, confirming batch‑to‑batch reproducibility.
In carpet pre‑coat and secondary‑backing compounds, CW40-907 is incorporated at **12–15 %** of the weight of calcium carbonate filler (typical Filler loading **600 phr**). The aqueous compound is frothed with a Hobart mixer to a wet density of **0.15–0.40 g/cm³**, knife‑coated onto a polypropylene primary backing, and dried through a tenter frame at **120–150 °C** for **3–5 min**. Bond strength measured on a Zwick universal testing machine per **ASTM D3936‑17** (loop test, **300 mm/min**) exceeds **2.5 N/mm**, and the adhesive fracture mode remains cohesive within the foam, not adhesive at the interface. The elimination of APEOs removes a documented source of alkylphenol emission into indoor air, as volatilisation studies using emission test chambers ( **ISO 16000‑6** ) have detected nonylphenol in the chamber air of carpets bonded with APEO‑based latices at levels of **1–3 µg/m³** after **24 h**, whereas CW40-907‑backed specimens consistently yield values below the detection limit ( **<0.1 µg/m³** ). Froth stability is maintained via a dual‑surfactant package that balances low‑HLB and high‑HLB components, avoiding the foam collapse often encountered with some APEO‑free grades that rely on a single point of hydrophilic‑lipophilic balance.
Woodworking Adhesives: Setting Speed and Creep Resistance Under D3/D4 Classification
For hardwood assembly (beech, *Fagus sylvatica*) meeting **EN 204** durability class D3, a single‑component formulation with **45 %** CW40-907 on wet adhesive weight develops a shear strength of **>7 N/mm²** after **4 days** conditioning at **23 °C/50 % RH**, and retains **>4 N/mm²** following **4 h** cold‑water soak. The quick setting behaviour derives from the high molecular mass of the polyvinyl alcohol stabiliser, which induces a rapid viscosity build as water is absorbed by the wooden substrate. Creep resistance under **EN 14256** at **60 °C** with a static load of **0.15 N/mm²** for **6 h** yields a joint displacement **<0.5 mm**, a value that remains stable even when the adhesive is plasticised with **5 %** dibutyl phthalate, indicating robust internal cohesion. Compared with surfactant‑stabilised APEO‑free dispersions, CW40-907 does not require formaldehyde‑donor crosslinkers to meet D3 requirements, which keeps free formaldehyde content in the cured glue line below **5 µg/m³** when evaluated by the chamber method **EN 717‑1**.
Potential Incompatibilities and Storage‑Rheology Drift Over Shelf Life
Addition of polyvalent cations such as **Al³⁺** (e.g., from aluminium chloride accelerators) leads to instantaneous micro‑coagulation and grit formation; therefore, hardener components based on metal salts must be introduced slowly under high‑speed agitation and at a pH buffer maintained above **4.0**. Amine‑functional silanes, commonly used as adhesion promoters in parquet adhesives, may destabilise the colloid through electrostatic bridging; pre‑dilution of the silane to **20 %** in isopropanol and dropwise addition while monitoring Zeta potential is recommended. The product remains stable in its original sealed containers for **6 months** when stored at **5–30 °C**, protected from freezing. One freeze‑thaw cycle ( **-5 °C** to **23 °C** ) causes an irreversible viscosity increase of **+300 %** and formation of a gritty deposit. During compounding, pH should not be permitted to rise above **8.0**, as alkaline hydrolysis of the ester linkages accelerates and releases alcohol species that plasticise the film and increase the water absorption coefficient (measured at **24 h** immersion per **ISO 62** ) from the typical **15 %** to **>25 %**.
The table below contrasts CW40-907 against a representative APEO‑containing VAE (standard grade CW40‑705) and a commercial APEO‑free competitor grade to highlight structural and performance differences across key parameters.
| Parameter | CW40-907 | CW40-705 (APEO‑containing) | APEO‑free competitor A | Method |
|---|
| MFFT (°C) | <0 | 3 | 5 | ISO 2115 |
| APEO content (mg/kg) | <10 | 1 800–2 200 | <15 | EN ISO 18254‑1 |
| Wet shear strength on beech after 4 h water soak (N/mm²) | 4.5 | 3.8 | 3.2 | EN 204 D3 |
| Formaldehyde content (mg/kg) | 15 | 25 | 30 | EN 717‑3 |
| Daphnia EC50 48 h (mg/L) | >100 | 7 | >100 | OECD 202 |
| Water absorption after 24 h (%) | 15 | 22 | 19 | ISO 62 (film cast) |
The data illustrate that the APEO‑free architecture in CW40-907 not only meets the regulatory cut‑off but also delivers a measurable gain in hygrothermal resistance, likely attributable to the absence of the polyethylene oxide segments that promote water uptake in traditional APEO‑bearing analogues.
